Auto Window Tinting Done Right the First Time

Most passenger cars take 2 to 3 hours. SUVs, trucks, and vehicles with complex rear window shapes may run 3 to 4 hours. We'll give you an accurate time estimate when you book so you can plan your day around the appointment.

Wait at least 3 full days before rolling your windows down. The film's adhesive needs time to bond completely to the glass. Rolling windows down too soon is one of the most common causes of edge peeling, and it's entirely preventable.

Yes, within specific limits. Florida law permits front side windows at 28% VLT minimum, and rear side and back windows at 15% VLT for sedans or 6% VLT for SUVs and trucks. Every job we complete is verified against Florida's current tint law before you leave our shop, guaranteed street-legal.

Carbon film is a high-performing mid-range film with strong heat and UV rejection and a clean matte finish that holds its color over time. Ceramic film is the top-tier option; it delivers the highest heat rejection available, superior optical clarity, and zero signal interference. Both are excellent; ceramic is the better choice if maximum cabin comfort is your priority.

No. Ceramic film contains no metal, which means it does not interfere with GPS, Bluetooth, cell signal, radar detectors, or any electronic system in your vehicle. This is one of the main advantages ceramic has over older metallic films, which could cause signal issues. You get maximum performance without any electronic trade-offs.

Professional-grade film installed correctly lasts many years. Dyed film typically lasts 3 to 5 years before showing signs of fading. Carbon film holds up well for 5 to 10 years. Ceramic film, installed properly, can last well over a decade. Cheap aftermarket film bought online and self-applied tends to bubble, peel, or purple-fade within 1 to 2 years.

Yes. Window film can be removed professionally without damaging the glass. We strongly advise against DIY removal — improper technique frequently leaves adhesive residue on the glass and risks scratching the window. If you need tint removed, call us and we'll handle it cleanly.

Bubbling and peeling are almost always the result of poor installation, low-quality film, or both. Common culprits include inadequate surface prep before application, film that wasn't trimmed precisely to the glass edge, rolling windows down before the adhesive has fully cured, or using harsh cleaning chemicals on the tint after installation. A proper professional install — using quality film — eliminates all of these failure points.

Yes, and it's completely normal. During the first few days after installation you may notice a slight milky haze or small water pockets under the film. This is residual moisture from the installation process that evaporates as the film cures. It typically clears within 3 to 7 days depending on weather. Do not try to push out bubbles or squeegee the glass during this period.

Wait at least two weeks before cleaning tinted windows. After that, use a soft microfiber cloth and an ammonia-free window cleaner. Ammonia-based products degrade window film adhesive over time and will cause premature peeling. Never use rough scrubbing pads, steel wool, or abrasive cleaning tools on tinted glass.

Florida law only allows non-reflective tint on the top portion of the windshield above the AS-1 line — typically the top four to six inches. This strip helps reduce glare from overhead sunlight. Tinting the full windshield in any shade is not legal in Florida and we do not install it. We'll show you exactly what's permissible on your windshield during your estimate.

Measurably, yes. Quality window film — particularly carbon or ceramic — can reduce the solar heat entering your vehicle by 40 to 60 percent. In practical terms, that translates to a noticeably cooler cabin temperature when you get in, less A/C strain during your drive, and meaningful protection from UV exposure on long commutes through Brevard County.

We do a complete walkthrough inspection with you before you leave the shop specifically so any issues can be caught and addressed on the spot. If an installation defect appears after the curing period — genuine bubbling, lifting edges, or inconsistencies caused by our process — we'll make it right. Our reputation in Rockledge depends on every job leaving our shop correctly.

Yes. If you manage a fleet of work vehicles in Rockledge or anywhere in Brevard County, we offer fleet pricing and can schedule multiple vehicles to minimize business downtime. Call us directly at (321) 487-7939 to discuss your fleet size and we'll put together a custom quote.

Pricing depends on the vehicle type, the number of windows, and the film selected. A standard sedan with carbon film is priced differently than a full-size SUV with ceramic film. We don't publish flat rates online because we don't believe in quoting prices before we know your vehicle. What we can promise: our pricing is transparent, our estimates are free, and there are no hidden fees or bait-and-switch charges on any job we take. Call (321) 487-7939 or use our free estimate form to get your number.